3COM ROUTER 5000/6000 FAMILY
QUICK REFERENCE GUIDE
Overview
This Command Reference applies to the following Router 5000/6000 models running software version 3.0.
Router 5012 (3C13701)
Router 5232 (3C13751)
Router 5642 (3C13755)
Router 5682 (3C13701)
Router 6040 (3C13840)
Router 6080 (3C13880)
About the Command Line Interface
To use and navigate the command line interface of your unit, please refer to the following points for assistance:
■
When initially accessing the command line interface, press Enter when prompted. The User View menu for the unit
displays. This is indicated by the chevron brackets around the name of the unit at the prompt, for example,
<router5000-xx> (where xx is either EI or SI).
■
When in the System View menu, square brackets appear around the name of the unit at the prompt, for example,
[router5000-xx].
■
■
■
You must be in the System View menu to access the configurable CLI commands.
Some commands can be entered directly at any prompt from anywhere in the interface.
If you enter part of a command followed by a ? (with no space between), the CLI will show you all the commands
that begin in that way.
■
■
■
■
The term ‘view’ may be used interchangeably with the term ‘menu’.
The undo command is placed before the command you wish to undo, for example, undo setauthentication password.
<CTRL-A> places the cursor back to the start of the command line.
Enter the first few characters of a command and press TAB to enter the full command without having to input the
entire command (where there is only one command that starts with the entered characters).
■
■
■
Use the Up Arrow key at the prompt to repeat the previous command string.
Use the Delete key to delete the character after the cursor; the Backspace key deletes the character before the cursor.
When entering physical port numbers, Enter the port number as x/0/z, where x is the unit number and z is the
physical port number.
Copyright © 2006, 2007 3Com Corporation. All rights reserved.
www.3Com.com
Part Number: 10016467 Rev. AA
Published: October 2007
3Com Router 5000/6000 Family
Command Reference
3
abr-summary
Use the abr-summarycommand to configure the route aggregation on the area border router (ABR).
OSPF Area view
ISP Domain view
System view
access-limit
acl-reflect timeout
acl
Use the access-limitcommand to configure a limit to the amount of supplicants in the current ISP domain.
Use the acl-reflect timeoutcommand to set the global aging time of reflexive ACLs.
Use the aclcommand to create an access control list and enter ACL view.
System View
acl
Use the aclcommand to reference an ACL to control call-in and call-out of VTY (Telnet and SSH) users.
Use the accountingcommand to configure an accounting scheme for the current ISP domain.
User Interface view
ISP Domain view
accounting
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS accounting servers.
RADIUS Scheme view
RADIUS Scheme view
TACACS+ view
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS accounting servers.
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ accounting servers.
accounting commands
accounting domain
Use the accounting commandscommand to enable the system to start per-command accounting for
terminal users logged into the user interface.
User Interface view
Use the accounting domaincommand to enable DHCP server accounting for addresses from the global
DHCP address pools and configure a domain for DHCP accounting.
DHCP Address Pool view
accounting-on
Use the accounting-on enablecommand to enable the user re-authentication at reboot function.
Use the accounting optionalcommand to enable optional accounting.
RADIUS view
accounting optional
ISP Domain view
RADIUS view
activate
Use the activatecommand to activate the ADSL interface.
Use the activatecommand to enable the G.SHDSL interface.
ATM (ADSL) Interface view
activate
ATM (G.SHDSL) Interface view
activation-key
Use the activation-keycommand to define a shortcut key or key combination for starting a terminal
session.
User Interface view
Voice Entity view
address
Use the addresscommand to configure the voice routing policy to the peer voice gateway.
4
3Com Router 5000/6000 Family
Command Reference
address
Use the addresscommand to configure a route to the peer voice gateway or assign an X.121 address for
a destination host.
Voice Entity view
Voice Entity view
address sip
Use the address sipcommand to set routing policy for reaching the remote voice gateway (VG) to SIP.
adsl standard
adsl tx_attenuation
adv-factor
Use the adsl standardcommand to set the standard applied to the ADSL interface.
ATM (ADSL) Interface view
ATM (ADSL) Interface view
Use the adsl tx_attenuationcommand to set attenuation value for ADSL transmit power.
Use the adv-factorcommand to configure the advantage factor which is used to count Mos and ICPIF
value in a jitter voice test.
HWPing Test Group view
aggregate
aggregate
Use the aggregatecommand to establish an aggregated record in the BGP routing table.
Use the aggregatecommand to create a multicast aggregated record in the BGP routing table.
BGP view
Use the aggregatecommand without parameters to create one local aggregated route and set atomic
aggregation attributes.
IPv4 Multicast Subaddress Family view
aging-time
Use the aging-timecommand to configure SYN status waiting timeout value and FIN status waiting timeout
value of TCP, session entry idle timeout value of TCP and UDP.
ASPF Policy view
ah authentication-algorithm
Use the ah authentication-algorithmcommand to set the authentication algorithm adopted by
Authentication Header protocol in IPSec proposal.
Use the undo ah authentication-algorithmcommand to restore the default setting.
IPSec Proposal view
ahdsl annex
Use the shdsl annexcommand to configure annex standard at an SHDSL interface. You cannot activate a
link with different standard types at its two ends.
ATM (G.SHDSL) Interface view
alarm (CT3 Interface)
alarm-threshold
algorithm-suite
allow l2tp
Use the alarmcommand to enable the CT3 interface to detect/send alarm signals.
CT3 Interface view
Use the alarm-thresholdcommand to configure the alarm thresholds on the CT1/PRI interface as needed.
CT1/PRI Interface view
Use the algorithm-suitecommand to specify the algorithm suite used when a client registers.
Dvpn-Class view
Use the allow l2tpcommand to specify the name of the peer end of the tunnel on receiving call and the
Virtual-Template it uses.
L2TP Group view
DLCI view
annexg
ani
Use the annexgcommand to enable T1.617 Annext G on the frame relay interface for data transmission.
Use the anicommand to enable or disable the terminating point to send the calling party information
(service category and calling number) to the originating point during call connecting process.
R2 CAS view
3Com Router 5000/6000 Family
Command Reference
5
ani-offset
Use the ani-offsetcommand to configure the number of digits of the called number to be collected prior
to requesting the calling party information.
R2 CAS view
R2 CAS view
answer
Use the answercommand to configure whether the terminating point is required to send answer signal.
apply access-vpn vpn-instance
Use the apply access-vpn vpn-instancecommand to specify to search private network forwarding routes
in vpn-name1, vpn-name2, vpn-name3, vpn-name4, vpn-name5, vpn-name6 (if they all
exist)and forward packets after policy routing is enabled to satisfy route-policy.
Route-Policy view
apply as-path
Use the apply as-pathcommand to specify the AS numbers to be added in front of the original AS path in
route-policy.
Routing Policy view
Routing Policy view
Routing Policy view
Routing Policy view
Route-Policy view
Routing Policy view
Route-Policy view
Route-Policy view
Route-Policy view
Route-Policy view
Route-Policy view
apply community
apply cost
Use the apply communitycommand to set BGP community attributes in route-policy.
Use the apply costcommand to set the route cost value of route information.
Use the apply cost-typecommand to set the route cost type of route information.
apply cost-type
apply default output-interface
Use the apply default output-interfacecommand to set default forwarding interface for packets.
apply ip-address
Use the apply ip-addresscommand to set the next hop address of route information.
apply ip-address default next-hop
Use the apply ip-address default next-hopcommand to set the default next hop of a packet.
apply ip-address next-hop (for Multicast Policy Routing)
Use the apply ip-addresscommand to configure the next hop IP address list in a route-node.
apply ip-address next-hop (for Unicast Policy Routing)
Use the apply ip-address next-hopcommand to set the packet next hop.
apply ip-dscp
apply ip-precedence
apply isis
Use the apply ip-dscpcommand to configure to modify the packet DSCP value matching the policy.
Use the apply ip-precedencecommand to set precedence of IP packets.
Use the apply isiscommand to apply the level of a matched route to be redistributed to Level-1, Level-2
or Level-1-2.
Routing Policy view
Routing Policy view
apply local-preference
Use the apply local-preferencecommand to apply the local preference of route information.
apply mpls-label
Use the apply mpls-labelcommand to assign MPLS labels for public network routes that match
route-policy filter conditions.
Route-Policy view
6
3Com Router 5000/6000 Family
Command Reference
apply origin
Use the apply origincommand to set the routing source of BGP routing information.
Routing Policy view
apply output-interface (for Multicast Policy Routing)
Use the apply output-interfacecommand to configure an outgoing interface list in a route-node.
Route-Policy view
Route-Policy view
apply output-interface (for Unicast Policy Routing)
Use the apply output-interfacecommand to set a packet forwarding interface.
apply policy outbound
Use the apply policy outboundcommand to set the frame relay virtual circuit queuing to CBQ
(Class-Based Queuing).
Frame Relay Class view
Routing Policy view
apply tag
Use the apply tagcommand to set the tag area of OSPF route information.
Use the areacommand to enter OSPF area view.
area
OSPF view
OSPF Area view
area
Use the areacommand to configure the type of busy tone detection for FXO voice subscriber-line.
Voice Subscriber-line view
area-authentication-mode
Use the area-authentication-modecommand to configure IS-IS to authenticate the received Level-1
routing information packets (LSP, CSNP and PSNP), according to the pre-defined mode and password.
IS-IS view
Voice Entity view
area-id (Voice Entity view)
Use the area-idcommand to configure the area ID of voice GW.
area-id (Voice GK Client view)
Use the area-idcommand to configure the H.323 gateway area ID.
Voice GK Client view
arp check enable
Use the arp check enablecommand to enable ARP entry check to have the device not learn the ARP
entries with broadcast MAC addresses.
System view
Ethernet interface view
Ethernet Interface view
Ethernet Interface view
arp-proxy enable
arp security
Use the arp-proxy enablecommand to enable proxy ARP on an interface.
Use the arp securitycommand to disable dynamic ARP learning on an Ethernet interface.
Use the arp security time-outcommand to configure the aging time of the authorized ARP entries.
arp security time-out
arp send-gratuitous-arp
Use the arp send-gratuitous-arpcommand to enable sending gratuitous ARP packet on this interface
periodically and set the sending period.
Bridge Template view
Ethernet Interface view
Ethernet Subinterface view
Gigabit Ethernet Interface view
Gigabit Ethernet Subinterface view
Virtual Ethernet interface view
VLAN Interface view
arp static
Use the arp staticcommand to configure ARP mapping table.
System view
3Com Router 5000/6000 Family
Command Reference
7
arp timer aging
Use the arp timer agingcommand to set the aging timer for dynamic ARP entries.
System view
OSPF view
asbr-summary
ascii
Use the asbr-summarycommand to configure summarization of redistributed routes by OSPF.
Use the asciicommand to set the type of the transmitted data to ASCII.
FTP Client view
aspf-policy
Use the aspf-policycommand to define an ASPF policy. For a defined policy, the policy can be invoked
through its policy number.
System view
async mode
Use the async modecommand to set the operating mode of the asynchronous serial interface.
Asynchronous Serial Interface view
AUX Interface view
AM Interface view
async mode padpos
Use the async mode padposcommand to configure a POSPAD access port.
Asynchronous Serial Interface view
AUX Interface view
async mode pos
Use the async mode pospos-numbercommand to create a POS access port in nontransparent
transmission and permanent TCP connection mode.
Asynchronous Serial Interface view
AM Interface view
FCM Interface view
AUX Interface view
async mode posapp
Use the async mode posappcommand to configure the interface to operate in POS application mode.
Asynchronous Serial Interface view
AUX Interface view
atm-class
Use the atm-classcommand to apply a set of parameters (which are defined in ATM-Class) to an ATM
interface or a PVC.
Interface view
PVC view
atm class
Use the atm classcommand to create an ATM-Class and enter the ATM-Class view.
Use the atm-cttcommand to set all interfaces on a board to transparent transmission.
System view
atm-ctt
ATM Interface view
atm-link check
Use the atm-link checkcommand to have the protocol state of the ATM P2P subinterface changes
depending on whether the physical interface is up and whether a PVC is configured on the subinterface.
ATM P2P Subinterface view
authentication
authentication
Use the authenticationcommand to configure an authentication scheme for the current ISP domain.
ISP Domain view
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS authentication servers.
RADIUS Scheme view
authentication
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authentication servers.
TACACS+ view
8
3Com Router 5000/6000 Family
Command Reference
authentication
Use the authenticationcommand to enable user authentication and authorization for the access service
number.
Voice Access-Number view
authentication
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authentication servers.
TACACS+ view
authentication-algorithm
Use the authentication-algorithmcommand to select the authentication algorithm for an IKE proposal.
IKE Proposal view
authentication-client method
Use the authentication-client methodcommand to specify how the DVPN server that applies the DVPN
policy authenticates clients. None, CHAP, and PAP are currently available.
Dvpn-Policy view
Voice AAA view
authentication-did
authentication-method
authentication-mode
Use the authentication-didcommand to enable authentication for all one-stage dial (direct dial) users.
Use the authentication-methodcommand to select the authentication method used by an IKE proposal.
Use the authentication-modecommand to set the authentication mode at login.
IKE Proposal view
Use the authentication-mode nonecommand to set the authentication mode to none, that is, no
authentication at login.
User Interface view
OSPF Area view
Dvpn-Class view
authentication-mode
Use the authentication-modecommand to configure one area of OSPF to support the authentication
attribute.
authentication-server method
Use the authentication-server methodcommand to specify a client whether or not to authenticates the
DVPN server it accesses.
authentication super hwtacacs-scheme
Use the authentication super hwtacacs-schemecommand to configure super authentication scheme for
a domain.
ISP Domain view
ISP Domain view
authorization
authorization
Use the authorizationcommand to configure an authorization scheme for the current ISP domain.
Use the authorizationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authorization servers.
TACACS+ view
Voice Entity view
System view
authorization-level
auto-config
Use the authorization-levelcommand to configure a local caller authorization level for the voice entity.
Use the auto-configcommand to implement the auto-configoperation.
auto-config enable
auto-execute command
Use the auto-config enablecommand to enable auto-config.
System view
Use the auto-execute commandcommand to set a command to be automatically executed.
User Interface view
3Com Router 5000/6000 Family
Command Reference
9
balance
Use the balancecommand to configure the number of routes participating in BGP load balancing.
BGP view
System view
band-based-sharing
baudrate
Use the band-based-sharingcommand to enable bandwidth-based unbalanced load sharing.
Use the baudratecommand to set the baud rate of a serial interface.
Use the bertcommand to set test error bit for line Bit.
Serial Interface view
CE3 interface view
CT1/PRI Interface view
CT3 Interface view
System view
bert
bert (CT1/PRI Interface)
Use the bertcommand to start a BERT test on the CT1/PRI interface.
bert (CT3 Interface)
Use the bertcommand to start a BERT test on the CT3 interface.
bgp
Use the bgpcommand to enable BGP and enter the BGP view.
This command is used to enable and disable BGP as well as to specify the local AS number of BGP.
bims boot request
Use the bims boot requestcommand to enable the BIMS device to access the branch intelligent
management system (BIMS) center at startup.
System view
bims device-id string
Use the bims device-idcommand to configure the unique identifier of the BIMS device at the BIMS center.
Use the bims enablecommand to enable BIMS.
System view
System view
bims enable
bims interval
Use the bims intervalcommand to configure the interval for accessing the BIMS center. When the interval
is set to 0, the BIMS device does not access the BIMS center regularly.
System view
System view
System view
bims ip address
bims request
bims-server
Use the bims ip addresscommand to configure the IP address and port number of the BIMS center.
Use the bims requestcommand to have the BIMS device access the BIMS center.
Use the bims-servercommand to enable and configure BIMS option for a global address pool on the
DHCP server.
Global DHCP Address Pool view
bims sharekey
Use the bims sharekeycommand to configure the shared key between the BIMS device and the BIMS
center.
System view
System view
bims source ip-address
Use the bims source ip-addresscommand to specify a source IP address for the packets sent by the
BIMS device. It can be the IP address of a port on the router.
bims specify-time
Use the bims specify-timecommand to configure the BIMS device to access the BIMS center at the
specified time and if desired, configure the device to access the BIMS center at regular intervals from then
on during a specified period.
System view
10
3Com Router 5000/6000 Family
Command Reference
binary
Use the binarycommand to set data type to binary for file transfer.
Use the boot bootromcommand to upgrade BootRom.
FTP Client view
System view
System view
System view
boot bootrom
boot bootrom
bootfile backup
bootfile dir
Use the boot bootromcommand to upgrade BootRom.
Use the bootfile backupcommand to specify the backup boot file.
Use the bootfile dircommand to view information about all the boot files in the Flash, including file type,
date, time, file size, and file name.
System view
System view
System view
System view
bootfile main
Use the bootfile maincommand to specify the main boot file.
bridge aging-time
Use the bridge aging-timecommand to configure the aging time of the dynamic address table.
bridge bridge-set enable
Use the bridgebridge-setenablecommand to enable the specified bridge set.
bridge bridging
Use the bridge bridgingcommand to enable the bridging function of a network layer protocol on a
specified bridge set.
System view
System view
System view
System view
bridge enable
Use the bridge enablecommand to enable the bridging function.
bridge learning
bridge mac-address
bridge routing
Use the bridge learningcommand to enable forwarding by dynamic address table.
Use the bridge mac-addresscommand to manually configure a static address table entry of bridge.
Use the bridge routingcommand to enable the routing function of a specified bridge-set for the specified
network protocol.
System view
System view
bridge routing-enable
Use the bridge routing-enablecommand to enable the routing function of the bridge.
Use the bridge setcommand to add an interface to a bridge set.
bridge-set
Interface view
Bridge Template view
bridge-set (Ethernet Interface view)
Use the bridge-set (in the Ethernet Interface view)command to add the Ethernet interface into the
bridge.
Ethernet Interface view
bridge set (Synchronous Serial Interface view)
Use the bridge-set (in Synchronous serial interface system view)command to add the
synchronous serial interface encapsulated into SDLC into the bridge group.
Synchronous Serial Interface view
3Com Router 5000/6000 Family
Command Reference
11
bridge-set stp enable
Use the bridge-set stp enablecommand to disable STP on the port.
Interface view
Interface view
Interface view
System view
System view
System view
System view
System view
bridge-set stp port pathcost
Use the bridge-set stp port pathcostcommand to configure the path cost of the bridge port.
bridge-set stp port priority
Use the bridge-set stp port prioritycommand to configure the priority of the bridge port.
bridge stp ieee
Use the bridge stp ieeecommand to specify a bridge set to support IEEE STP.
Use the bridge stp max-agecommand to set the Max Age timer on the bridge.
Use the bridge stp prioritycommand to assign a priority to the bridge.
bridge stp max-age
bridge stp priority
bridge stp timer forward-delay
Use the bridge stp timer forward-delaycommand to set the Forward Delay timer on the bridge.
bridge stp timer hello
Use the bridge stp timer hellocommand to set the Hello Time timer on the bridge.
bridge vlanid-transparent-transmit enable
Use the bridge vlanid-transparent-transmit enablecommand to enable VLAN ID transparent
transmission.
Interface view
broadcast-limit link
Use the broadcast-limit linkcommand to configure the maximum number of links that the virtual
template supports for sending multicast or broadcast packets.
Virtual Template view
Ethernet Port view
PIM view
broadcast suppression
Use the broadcast-suppressioncommand to restrict the broadcast traffic size on the port.
Use the bsr-policycommand to restrict the range for valid BSR, preventing BSR spoofing.
bsr-policy
bump
Use the bumpcommand to configure the standby PVC that will take over when a specified PVC goes down.
ATM Pvc-Group view
busytone-t-th
Use the busytone-t-thcommand to configure the threshold of busy tone detection.
FXO Voice Subscriber-Line view
FTP Client view
bye
Use the byecommand to disconnect from the remote FTP server and exit to user view.
bye
Use the byecommand to terminate the connection to the remote SFTP server and exit to system view as
you would with the exitand quitcommands.
SFTP Client view
PIM view
c-bsr
c-rp
Use the c-bsrcommand to configure a candidate BSR.
Use the c-rpcommand to configure the router to advertise itself as a candidate RP to BSR.
PIM view
12
3Com Router 5000/6000 Family
Command Reference
ca identifier
Use the ca identifiercommand to specify the CA this device trusts and have the "name" CA bound with
this device.
PKI Domain view
CE1/PRI Interface view
ATM E1/T1 Interface view
cable
cable
cable
Use the cablecommand to set the cable length matching the CE1/PRI interface.
Use the cablecommand to set the cable length of the ATM E1 interface.
Use the cablecommand to configure the cable mode of ATM T3 cable, i.e., to set the distance between the
router and the cable distribution frame.
ATM T3 Interface view
cable (CT1/PRI Interface)
Use the cablecommand to set cable attenuation and length on a CT1/PRI interface to match the distance
of the transmission line.
CT1/PRI Interface view
CT3 Interface view
MSDP view
cable (CT3 Interface)
cache-sa-enable
call-mode
Use the cablecommand to configure the length of the cable with which a CT3 interface is connected.
Use the cache-sa-enablecommand to enable the router to cache SA state.
Use the call-modecommand to configure a call-mode for calls between local router and peer router.
Voice Entity view
callednumber receive-method
Use the callednumber receive-methodcommand to enable the device to place a call immediately after all
digits of the called number are collected or after a pound sign (#), the terminator, is received.
Use the caller-permit command to configure the calling numbers that are permitted to call in.
Use the carcommand to configure traffic monitoring for a behavior.
Voice Access-Number view
caller-permit
Voice Entity view
car
Traffic Behavior view
card-digit
Use the card-digitcommand to configure the number of digits in a card number for an access service
number.
Voice Access-Number view
cas
cbs
Use the cascommand to enter the R2 CAS view and digital E&M Signaling view.
Use the cbscommand to set the committed burst size of frame relay virtual circuit.
CE1/PRI Interface view
Frame Relay Class view
System view
ccc interface out-interface
Use the ccc interface out-interfacecommand to create a local CCC connection.
ccc interface transmit-lsp receive-lsp
Use the ccc interface transmit-lsp receive-lspcommand to create a remote CCC connection.
System view
cd
Use the cdcommand to change the current path on the SFTP server. If you do not specify the remote-path
argument, the current path is displayed.
SFTP Client view
3Com Router 5000/6000 Family
Command Reference
13
cd
Use the cdcommand to change the current working directory of the user to the specified directory.
User view
FTP Client view
Voice AAA view
SFTP Client view
FTP Client view
MPLS L2VPN view
PVC view
cd
Use the cdcommand to change the current working directory path on the remote FTP server.
Use the cdrcommand to configure the saving rule for call detail record.
Use the cdupcommand to quit to the upper directory.
cdr
cdup
cdup
Use the cdupcommand to return from the current working directory path to the upper directory.
Use the cecommand to create a CE or modify the CE range.
ce
cell-packing
Use the cell-packingcommand to set the maximum number of cells to be packed in one PVC.
certificate request entity
Use the certificate request entitycommand to specify the name of the entity for certificate request.
PKI Domain view
certificate request from
Use the certificate request fromcommand to choose between CA and RA to register for certificate
request.
PKI Domain view
PKI Domain view
certificate request mode
Use the certificate request modecommand to decide between the manual or the auto request mode.
certificate request polling
Use the certificate request pollingcommand to specify the interval between two polls and the retry
times.
PKI Domain view
PKI Domain view
certificate request url
Use the certificate request urlcommand to specify the server URL for certificate request through
SCEP protocol. SCEP is a protocol specialized in the communication with authentication authorities.
channel
Use the channelcommand to add X.25 interface or XOT channel of one serial port to the current hunt group.
X.25 Hunt Group view
CE1/PRI Interface view
CT1/PRI Interface view
ISDN BRI Interface view
RIP view
channel-set (CE1/PRI Interface)
Use the channel-setcommand to bundle some timeslots of a CE1/PRI interface into a channel-set.
channel-set (CT1/PRI Interface)
Use the channel-setcommand to bundle timeslots on the CT1/PRI interface into a channel-set.
channel-set timeslot
checkzero
Use the channel-set timeslot command to configure a B channel for leased line service.
Use the checkzerocommand to check the zero field of RIP-1 packet.
cid display
Use the cid displaycommand to enable caller identification display.
Voice Subscriber-Line view
14
3Com Router 5000/6000 Family
Command Reference
cid enable
Use the cid enablecommand to enable CID on the FXO interface.
Voice Subscriber-Line view
cid select-mode
Use the cid select-modecommand to configure the route selection mode used by the calling party to set
up VoFR calls.
DLCI view
cid send
Use the cid sendcommand to enable the FXO or FXS module to send calling numbers to the IP side.
Voice Subscriber-Line view
cid type
Use the cid typecommand to configure the format of transmitted information about the calling party.
Voice Subscriber-Line view
Frame Relay Class view
Frame Relay Class view
Policy view
cir
Use the circommand to set the CIR of frame relay virtual circuit.
cir allow
Use the cir allowcommand to set the CIR ALLOW of frame relay virtual circuit.
Use the classifier behaviorcommand to specify the behavior for the class in the policy.
classifier behavior
clear-forward-ack
Use the clear-forward-ackcommand to enable or disable the terminating point to respond by sending a
clear-back signal when the originating point (calling party) disconnects a call.
R2 CAS view
System view
System view
clns enable
Use the clns enablecommand to enable CLNS.
clns erpacket enable
Use the clns erpacket enablecommand to enable generation of error report packets.
clns erpacket interval
Use the clns erpacket intervalcommand to set the minimum interval to generate two successive error
report packets.
System view
System view
System view
System view
System view
System view
clns es-peer
Use the clns es-peercommand to configure a static neighboring ES.
Use the clns netcommand to assign an NET address to the IS.
Use the clns rdpacket enablecommand to enable the router to send RD packets.
clns net
clns rdpacket enable
clns rdpacket interval
Use the clns rdpacket intervalcommand to set the minimum interval to generate RD packets.
clns route-static
Use the clns route-staticcommand to configure a static OSI route.
clns timer rdpacket holding
Use the clns timer rdpacket holdingcommand to set the holding time of the information a RD packet
carries.
System view
clock
Use the clockcommand to set the clock mode of the ATM E1/T1 interface.
ATM E1/T1 Interface view
3Com Router 5000/6000 Family
Command Reference
15
clock
Use the clockcommand to set the clock mode of ATM E3/T3 interface.
ATM E3/T3 Interface view.
ATM Interface view
clock
clock
clock
clock
Use the clockcommand to set the clock mode on an ATM interface.
Use the clockcommand to specify ATM interface to use internal transmission clock signal.
Use the clockcommand to set the clock mode of the CPOS interface.
Use the clockcommand to set the clock mode of the POS interface.
ATM Master Interface view
CPOS Interface view
POS Interface view
clock (CE1/PRI Interface)
Use the clockcommand to set the clock mode on a CE1/PRI interface.
CE1/PRI Interface view
CE3 Interface view
clock (CE3 Interface)
clock (CT1/PRI Interface)
Use the clockcommand to set clocking on the CT1/PRI interface.
CT1/PRI Interface view
CT3 Interface view
Serial intervace view
System view
clock (CT3 Interface)
Use the clockcommand to set the clock mode on the CT3 interface.
clock (Serial Interface)
Use the clockcommand to set clock selection mode for a synchronous serial interface.
clock datetime
Use the clock datetimecommand to set the current time and date of the router.
clock summer-time
Use the clock summer-timecommand to set the name, and starting and ending time of the daylight saving
time.
System view
System view
clock timezone
Use the clock timezonecommand to set local time zone information.
close
Use the closecommand to terminate the connection to the remote FTP server, but remain in FTP client
view.
FTP Client view
cng-on
Use the cng-oncommand to enable comfort noise function.
Voice Subscriber-Line view
cngced-detection
Use the cngced-detectioncommand to set the threshold parameters for CNG/CED signal detection.
Voice Subscriber-Line view
CE1/PRI Interface view
CT1/PRI Interface view
code (CEI/PRI Interface)
Use the codecommand to set the line code format for a CE1/PRI interface.
code (CT1/PRI Interface)
Use the codecommand to set the line code format on the CT1/PRI interface.
16
3Com Router 5000/6000 Family
Command Reference
code nrzi
Use the code nrzicommand to set the digital signal coding format to None-Return-to-Zero-Inverse (NRZI)
for a synchronous serial interface.
Synchronous Serial Interface view
code nrzi
Use the code nrzicommand to configure the NRZI encoding of the synchronous serial port.
Synchronous Serial Interface System view
System view
command-alias enable
command-alias mapping
command-privilege
Use the command-alias enablecommand to enable the command alias function.
Use the command-alias mapping command to map an alias to a keyword.
System view
Use the command-privilege levelcommand to assign a command level to the commands in a specified
view.
System view
common-name
Use the common-namecommand to specify the common name of an entity, take User name for example.
PKI Entity view
compare-different-as-med
Use the compare-different-as-medcommand to enable comparison of MED values of routes from
neighbors residing in different ASs when determining the best route.
BGP Unicast view
BGP Multicast view
VPNv4 view
compression
Use the compressioncommand to configure the voice coding method according to priority level.
Use the confederation idcommand to configure confederation identifier.
Voice Entity view
BGP view
confederation id
confederation nonstandard
Use the confederation nonstandardcommand, the router can be compatible with the AS confederation
not adopting RFC1965.
BGP view
BGP view
confederation peer-as
Use the confederation peer-ascommand to specify the sub-ASs constituting a confederation.
congestion-threshold
Use the congestion-thresholdcommand to enable congestion management function of frame relay virtual
circuit.
Frame Relay Class view
connection
Use the connectioncommand to create a CE connection.
MPLS L2VPN CE view
connection-limit default
Use the connection-limit defaultcommand to configure the action when the limit policy is not available.
System view
System view
System view
System view
connection-limit default amount
Use the connection-limit default amountcommand to set default threshold for connection limit.
connection-limit enable
Use the connection-limit enablecommand to enable the connection limit function.
connection-limit policy
Use the connection-limit policycommand to create connection limit policy and enter its view.
3Com Router 5000/6000 Family
Command Reference
17
controller cpos
Use the controller cposcommand to enter CPOS interface view.
System view
System view
controller e1
controller e3
controller t1
controller t3
copy
Use the controller e1command to enter CE1/PRI interface view.
Use the controller e3command to enter the CE3 interface view.
Use the controller t1command to enter a CT1/PRI interface view.
Use the controller t3command to enter the CT3 interface view.
Use the copycommand to copy a file.
System view
System view
System view
User view
cost-style
count
Use the cost-stylecommand to set the cost type of an IS-IS packet received/sent by the router.
Use the countcommand to configure the number of packets to be sent for each test.
IS-IS view
HWPing Test Group view
country
Use the countrycommand to specify the code of the country to which the entity belongs. It is a standard
2-byte code, e.g., CN for China.
PKI Entity view
country-code
Use the country-codecommand to configure the coding format of the modem connected to the serial
interface.
Asynchronous Serial Interface view,
AM Interface view
cptone
Use the cptonecommand to set the prompt tone played on the current voice subscriber-line to the specified
country mode.
Voice Subscriber-Line view
cpu-usage cycle
Use the cpu-usage cyclecommand to set the CPU usage statistic interval.
Use the crccommand to set the CRC length on the POS interface.
Use the crccommand to configure CRC mode of the serial interface formed by CE1.
Use the crccommand to configure CRC mode of the serial interface formed by CE3.
Use the crccommand to configure CRC mode of the serial interface formed by CT1.
Use the crccommand to configure CRC mode of the serial interface formed by CT3.
System view
crc
POS Interface view
crc
Synchronous Serial Interface view
Synchronous Serial Interface view
Synchronous Serial Interface view
Synchronous Serial Interface view
PKI Domain view
crc
crc
crc
crl check disable
Use the crl check disablecommand to disable CRL checking.
18
3Com Router 5000/6000 Family
Command Reference
crl update-period
Use the crl update-periodcommand to specify the update period of CRL, which is the interval between
local downloads of CRLs from CRL access server.
PKI Domain view
PKI Domain view
crl url
Use the crl urlcommand to specify the distribution point URL for CRL.
crp-policy
Use the crp-policycommand to restrict the range for valid C-RP and the group range served by each
C-RP, preventing C-RP cheating.
PIM view
CT3 Interface view
BGP view
ct1 alarm
Use the t1 alarmcommand to enable the specified T1 line on the CT3 interface to detect/send alarm
signals.
dampening
Use the dampeningcommand to make BGP route dampening valid or modify various BGP route dampening
parameters.
data algorithm-suite
Use the data algorithm-suitecommand to specify the algorithm suite used by IPSec SA (security
association) to forward data.
Dvpn-Policy view
data-coding (CT1/PRI Interface)
Use the data-coding normalcommand to disable user data inversion on the CT1/PRI interface.
Use the data-coding invertedcommand to enable user data inversion on the CT1/PRI interface.
CT1/PRI Interface view
data-flow-format
data-flow-format
Use the data-flow-formatcommand to configure the unit in which data flows are sent to a RADIUS Server.
Use the data-flow-formatcommand to configure the unit of data flows sent to the TACACS server.
RADIUS view
TACACS+ view
data ipsec-sa duration time-base
Use the data ipsec-sa duration time-basecommand to set the lifetime of the IPSec SA used to encrypt
DVPN data.
Dvpn-Policy view
User Interface view
databits
Use the databitscommand to set data bits on the user interface.
Use the datafillcommand to configure the data for padding test packets.
Use the datasizecommand to configure the size of test packets.
datafill
HWPing Test Group view
HWPing Test Group view
datasize
datetime local
Use the datetime localcommand to configure the Datetime information element in the Connect message
to use local time in an ISDN call.
PRI and BSV Voice Interface Voice Subscriber Line view
ddns domainname
ddns password
Use the ddns domainnamecommand to configure a domain name whose domain name-to-IP address
mapping on DNS needs update by using the service of the DDNS service provider.
DDNS Configuration view
Use the ddns passwordcommand to configure a password for accessing the DDNS service provider.
DDNS Configuration view
3Com Router 5000/6000 Family
Command Reference
19
ddns refresh
Use the ddns refreshcommand to request the DDNS service provider to notify the DNS server that the
bound IP address of the domain name specified by the ddns domainnamecommand has changed.
DDNS Configuration view
ddns server
Use the ddns-servercommand to specify a DDNS service provider and enter its view. At present, only
3322.org is available.
System view
ddns source interface
Use the ddns source-interfacecommand to configure the interface used for accessing the DDNS service
provider.
DDNS Configuration view
ddns username
Use the ddns usernamecommand to configure a user name for accessing the DDNS service provider.
DDNS Configuration view
FTP Client view
User view
debugging
Use the debuggingcommand to enable debugging.
debugging
Use the debuggingcommand to enable system debugging.
debugging l2tp
debugging arp packet
debugging aspf
debugging atm all
debugging atm error
debugging atm event
debugging atm packet
debugging bgp
Use the debugging l2tpcommand to enable L2TP debugging.
System view
User view
Use the debugging arp packetcommand to enable ARP packets debugging.
Use the debugging aspfcommand to enable ASPF debugging function.
Use the debugging atm allcommand to enable all the debugging switches of ATM.
Use the debugging atm errorcommand to enable the error debugging of ATM.
Use the debugging atm eventcommand to enable the event debugging of ATM.
Use the debugging atm packetcommand to enable the packet debugging of ATM.
Use the debugging bgpcommand to enable debugging of specified BGP packets and events.
User view
User view
User view
User view
User view
User view
debugging bgp mp-update
Use the debugging bgp mp-updatecommand to enable MBGP Update packet debugging.
User view
debugging bims all
debugging bridge
Use the debugging bims allcommand to enable BIMS debugging.
User view
Use the debugging bridgecommand to enable the debugging function of a bridge set.
User view
debugging clns clnp
Use the debugging clns clnpcommand to enable debugging for CLNS packets to display the contents of
all received/transmitted CLNP packets.
User view
20
3Com Router 5000/6000 Family
Command Reference
debugging clns echo
debugging clns rd
Use the debugging clns echocommand to enable debugging for Echo packets.
Use the debugging clns rdcommand to enable debugging for RD packets.
User view
User view
User view
User view
User view
User view
User view
User view
System view
User view
debugging clns routing
Use the debugging clns routingcommand to enable debugging for Layer 3 routing tables.
debugging connection-limit
Use the debugging connection-limitcommand to enable connection limit debugging.
debugging detect-group
Use the debugging detect-groupcommand to enable auto detect debugging.
debugging dhcp client
debugging dhcp relay
debugging dhcp server
debugging dialer
Use the debugging dhcp clientcommand to enable debugging on the DHCP client.
Use the debugging dhcp relaycommand to enable debugging on the DHCP-relay module.
Use the debugging dhcp servercommand to enable debugging on the DHCP server.
Use the debugging dialercommand to enable DCC debugging.
debugging dlsw
Use the debugging dlswcommand to enable DLSw debugging.
debugging dlsw ethernet-backup
Use the debugging dlsw ethernet-backupcommand to enable debugging for DLSw Ethernet redundancy.
User view
User view
User view
User view
User view
User view
User view
User view
debugging dlsw filter
Use the debugging dlsw filtercommand to enable debugging for DLSw filtering.
debugging dlsw packet
Use the debugging dlsw packetcommand to enable SSP packet debugging for DLSw.
debugging dlsw reachable-cache
Use the debugging dlsw reachable-cachecommand to enable DLSw reachability debugging.
debugging dlsw udp
debugging dns
Use the debugging dlsw udpcommand to enable UDP packet debugging for DLSw.
Use the debugging dnscommand to enable DNS client debugging.
Use the debugging dvpncommand to enable DVPN debugging.
debugging dvpn
debugging encrypt-card
Use the debugging encrypt-cardcommand to enable debugging on the specified or all encryption cards.
3Com Router 5000/6000 Family
Command Reference
21
debugging esis
Use the debugging esis eventcommand to enable debugging for ES-IS protocol-related events. You can
display event information using this command, such as changes of neighbor states, entries in Level 0
routing table, and interface states.
Use the debugging esis packetcommand to enable debugging for ES-IS packets. You display information
about received/transmitted ES-IS packets, such as packet size, packet type, packet HT, and Layer 2 and
Layer 3 address.
User view
User view
User view
User view
User view
debugging firewall
debugging fr
Use the debugging firewallcommand to enable the information debugging of the firewall packet filtering.
Use the debugging frcommand to enable frame relay information debugging.
debugging fr compress
Use the debugging fr compresscommand to enable FRF9 IPHC debugging of frame relay.
debugging fr compression
Use the debugging fr compression iphccommand to enable FRF20 IPHC debugging of frame relay.
debugging fr pvc-group
Use the debugging fr pvc-groupcommand to enable debugging for the specified PVC group or all PVC
groups.
User view
User view
User view
User view
User view
User view
User view
User view
debugging hdlc clns
debugging hwatacs
debugging hwping
debugging igmp
Use the debugging hdlc clnscommand to enable debugging for HDLC OSI packets.
Use the debugging hwtacacscommand to enable TACACS+ debugging.
Use the debugging hwpingcommand to enable HWPing debugging.
Use the debugging igmpcommand to enable IGMP debugging functions.
Use the debugging ikecommand to enable IKE debugging.
Use the debugging ike dpdcommand to enable IKE DPD debugging.
Use the debugging ip icmpcommand to enable the ICMP debugging.
debugging ike
debugging ike dpd
debugging ip
debugging ip count
Use the debugging ip countcommand to enable debugging for the IP Accounting module (the IP
Accounting).
User view
User view
User view
User view
debugging ip multicast-policy
Use the debugging ip multicast-policycommand to enable the debugging of IP multicast policy routing.
debugging ip netstream
Use the debugging ip netstreamcommand to enable NetStream debugging.
debugging ip urpf
Use the debugging ip urpfcommand to display the information on the rejected packets by URPF.
22
3Com Router 5000/6000 Family
Command Reference
debugging ipsec
Use the debugging ipseccommand to turn IPSec debugging on.
User view
debugging ipx packet
Use the debugging ipx packetcommand to enable IPX packet debugging switch to view the contents of
IPX packet received and transmitted.
User view
User view
User view
User view
User view
User view
debugging ipx ping
debugging ipx rip
Use the debugging ipx pingcommand to enable IPX Ping packet debugging switch to view the contents
of Ping packet received and transmitted.
Use the debugging ipx ripcommand to enable RIP debugging switch to view information on RIP packet
received and transmitted, routing changes and timer expiry.
debugging ipx rtpro-flash
Use the debugging ipx rtpro-flashcommand to turn on the debugging switch of route refreshing in the
IPXRM module.
debugging ipx rtpro-interface
Use the debugging ipx rtpro-interfacecommand to turn on the debugging switch of interface change
in the IPXRM module.
debugging ipx rtpro-routing
Use the debugging ipx rtpro-routingcommand to turn on the debugging switch of route change in the
IPXRM module.
debugging ipx sap
Use the debugging ipx sapcommand to enable IPX SAP debugging switch to view information on SAP
packet received and transmitted, routing changes and timer expiry.
User view
User view
User view
debugging isdn
debugging isis
Use the debugging isdncommand to enable ISDN debugging.
Use the debugging isiscommand to enable IS-IS debugging.
debugging isis es-adjacency
Use the debugging isis es-adjacencycommand to enable debugging for IS-IS protocol-related events
occur on neighboring ESs.
User view
debugging isis is-adjacency
Use the debugging isis is-adjacencycommand to enable debugging for IS-IS protocol-related events
occur on neighboring ISs.
User view
User view
User view
User view
debugging lapd
Use the debugging lapbcommand to enable LAPB debugging.
debugging llc2
Use the debugging llc2command to enable the LLC2 debugging.
Use the debugging llc2 packetcommand to enable U frame debugging for LLC2.
debugging llc2 packet
debugging local-server
Use the debugging local-servercommand to enable debugging for the local RADIUS authentication
server.
User view
3Com Router 5000/6000 Family
Command Reference
23
debugging mobile-ip advertise
Use the debugging mobile-ip advertisecommand to enable debugging for mobility agent
advertisements.
User view
User view
User view
User view
User view
User view
User view
User view
debugging mobile-ip mobile-router
Use the debugging mobile-ip mobile-routecommand to enable debugging for an MR.
debugging mobile-ip node
Use the debugging mobile-ip nodecommand to enable debugging for MIP packets and events.
debugging modem
Use the debugging modemcommand to enable Modem debugging.
Use the debugging mpls l2vpncommand to view L2VPN link information.
Use the debugging ldpcommand to enable debugging of LDP messages.
Use the debugging mpls lspmcommand to enable various LSP debugging.
Use the debugging msdpcommand to enable MSDP debugging functions.
debugging mpls l2vpn
debugging mpls ldp
debugging mpls lspm
debugging msdp
debugging multicast forwarding
Use the debugging multicast forwardingcommand to enable multicast packet forwarding debugging
functions.
User view
User view
debugging multicast kernel-routing
Use the debugging multicast kernel-routingcommand to enable multicast kernel routing debugging
functions.
debugging multicast status-forwarding
Use the debugging multicast status-forwardingcommand to enable multicast forwarding status
debugging functions.
User view
User view
User view
User view
User view
debugging nat
Use the debugging natcommand to enable the NAT debugging function.
Use the debugging ntp-servicecommand to enable NTP service debugging.
Use the debugging ospfcommand to enable OSPF debugging.
Use the debugging padcommand to enable PAD debugging.
debugging ntp-service
debugging ospf
debugging pad
debugging physical
Use the debugging physicalcommand to enable debugging of the physical module on the specified
interface.
User view
User view
User view
debugging pim common
debugging pim dm
Use the debugging pim commoncommand to enable common PIM debugging functions.
Use the debugging pim dmcommand to enable PIM-DM debugging functions.
24
3Com Router 5000/6000 Family
Command Reference
debugging pim sm
debugging pki
Use the debugging pim smcommand to enable PIM-SM debugging functions.
Use the debugging pkicommand to enable PKI debugging functions.
Use the debugging portal command to enable portal debugging.
User view
Any view
User view
debugging portal
debugging pos
Use the debugging pos eventcommand to enable event debugging for the POS access service.
Use the debugging pos errorcommand to enable error debugging for the POS access service.
Use the debugging pos packetcommand to enable packet debugging for the POS access service.
Use the debugging pos allcommand to enable all debugging for the POS access service.
User view
User view
debugging pos-app
Use the debugging pos-appcommand to enable debugging for the specified or all POS applications.
debugging pos-interface
Use the debugging pos-interfacecommand to enable debugging for the specified or all POS access
ports.
User view
debugging ppp { all | cbcp | ccp | scp }
Use the debugging ppp { all | cbcp | ccp | scp }command to enable PPP related cbcp, ccp, scp or
all debugging.
User view
User view
debugging ppp { chap | pap }
Use the debugging ppp { chap | pap }command to enable PPP related CHAP or PAP debugging.
debugging ppp { core | ip | ipcp | lcp | lqc | mp }
Use the debugging ppp { core | ip | ipcp | lcp | lqc | mp }command to enable PPP related core,
ip, ipcp, lcp, lqc or mp debugging.
User view
User view
debugging ppp compression iphc rtp
Use the debugging ppp compression iphc rtpcommand to view debugging information about
IP/UDP/RTP header compression in IP header compression.
debugging ppp compression iphc tcp
Use the debugging ppp compression iphc tcpcommand to view the single packet information of the
IP/TCP header compression.
User view
User view
User view
User view
User view
User view
debugging pppoe-client
The command debugging pppoe-clientis used to enable PPPoE Client debugging switch.
Use the debugging pppofrcommand to enable PPPoFR debugging.
Use the debugging qllccommand to enable QLLC debugging.
debugging pppofr
debugging qllc
debugging radius
debugging rip
Use the debugging radiuscommand to enable RADIUS debugging.
Use the debugging ripcommand to enable RIP debugging.
3Com Router 5000/6000 Family
Command Reference
25
debugging rlogin
Use the debugging rlogincommand to enable remote login (rlogin) debugging.
User view
User View
User view
User view
debugging rsh
Use the debugging rshcommand to enable RSH debugging.
debugging sdlc
debugging slip
debugging snmp-agent
Use the debugging sdlccommand to enable the SDLC debugging.
Use the debugging slipcommand to enable the debugging switch of the SLIP protocol.
Use the debugging snmp-agentcommand to enable SNMP agent debugging and specify the information
to be output.
User view
User view
User view
User view
debugging standby event
Use the debugging standby eventcommand to enable debugging of the backup center.
debugging stp
Use the debugging stpcommand to enable STP debugging.
debugging ssh client
debugging ssh server
Use the debugging ssh clientcommand to enable SSH client debugging.
Use the debugging ssh servercommand to output information such as the negotiation process regulated
by SSH1.5 protocol to information center as debugging formation and to debug a user interface separately.
User view
User view
User view
debugging tcp event
debugging tcp md5
debugging tcp packet
Use the debugging tcp eventcommand to enable TCP events debugging.
Use the debugging tcp md5command to enable the MD5 authentication debugging of the TCP connection.
Use the debugging tcp packetcommand to enable the debugging of TCP connection. The number of
debugging switches users can enable is limited, that is, at the same time only a fixed number of debugging
switches can be enabled (combination of task ID and socket ID).
User view
User view
User view
User view
User view
User view
User view
debugging telnet
Use the debugging telnetcommand to enable Telnet connection debugging.
Use the debugging tunnelcommand to enable tunnel debugging.
debugging tunnel
debugging tftp-server
debugging udp-helper
debugging udp packet
debugging voice cm
Use the debugging tftp-servercommand to enable TFTP server debugging.
Use the debugging udp-helpercommand to enable UDP Helper debugging.
Use the debugging udp packetcommand to enable the debugging of UDP connection.
Use the debugging voice cmcommand to enable debugging for CM.
26
3Com Router 5000/6000 Family
Command Reference
debugging voice data-flow
debugging voice dpl
Use the debugging voice data-flowcommand to enable debugging for voice data processes.
User view
User view
User view
Use the debugging voice dplcommand to enable the debugging of voice dial program.
debugging voice fax
debugging voice h225
Use the debugging voice faxcommand to enable fax debugging.
Use the debugging voice h225command to enable debugging for the H.225.0 negotiation messages or
events.
User view
debugging voice h245
Use the debugging voice h245command to enable debugging for the H.245 negotiation messages or
events.
User view
User view
debugging voice ipp
debugging voice r2
Use the debugging voice ippcommand to enable H.323 recommendation suite module debugging.
Use the debugging voice r2command to enable the corresponding debugging in R2 signaling module.
Use the debugging voice r2 ccbcommand to view the information of the corresponding control block by
specifying the E1 port number and time slot number.
User view
debugging voice ras
debugging voice rcv
Use the debugging voice rascommand to enable the debugging information output switch of RAS
messages interacted between GK Client and GK Server.
User view
User view
Use the debugging voice rcvcommand to enable the debugging of the RCV module.
debugging voice rcv r2
Use the debugging voice rcv r2command to enable the debugging between the RCV module and the
R2 module of bottom layer.
User view
User view
User view
User view
User view
debugging voice sip
Use the debugging voice sipcommand to enable SIP debugging.
debugging voice sip rm
Use the debugging voice sip rmcommand to enable debugging for RM module.
debugging voice sip sm
Use the debugging voice sip cmcommand to enable debugging for SM module.
debugging voice vas
Use the debugging voice vascommand to enable the VAS module debugging.
debugging voice vas fax
Use the debugging voice vas faxcommand to enable the debugging of fax data access between the VAS
module and voice card.
User view
User view
User view
debugging voice vcc
debugging voice vmib
Use the debugging voice vcccommand to enable the debugging at various levels of the VCC module.
Use the debugging voice vmibcommand to enable the voice MIB module debugging.
3Com Router 5000/6000 Family
Command Reference
27
debugging voice vofr
Use the debugging voice vofrcommand to enable VoFR module debugging.
User view
User view
debugging voice vpp
Use the debugging voice vppcommand to enable the debugging of the VPP module.
debugging voice vpp r2
Use the debugging voice vpp r2command to enable the debugging between the VPP module and the
R2 module of bottom layer.
User view
User view
User view
User view
User view
debugging vrrp
debugging vty
Use the debugging vrrpcommand to enable VRRP debugging.
Use the debugging vtycommand to enable VTY debugging.
debugging web java-blocking
Use the debugging web java-blockingcommand to enable Java blocking debugging.
debugging web url-filter host
Use the debugging web url-filter hostcommand to enable the URL address filtering debugging.
debugging web url-filter parameter
Use the debugging web url-filter parametercommand to enable the URL parameter filtering
debugging.
User view
User view
debugging x25
debugging x25 x2t
debugging x25 xot
default
Use the debugging x25command to enable X.25 debugging.
Use the debugging x25 x2tcommand to enable X2T debugging.
Use the debugging x25 xotcommand to enable XOT debugging
System view
User view
Use the defaultcommand to restore the default of all the R2 configurations and reset the R2 call statistics
to 0.
R2 CAS view
OSPF view
default cost
default-cost
Use the default costcommand to configure the default cost for OSPF to redistribute external routes.
Use the default-costcommand to configure the cost of the default route transmitted by OSPF to the STUB
or NSSA area.
OSPF Area view
RIP view
default cost
Use the default costcommand to configure the default routing cost of a redistributed route.
default entity compression
Use the default entity compressioncommand to globally configure the mode of coding and decoding
as the default value.
Voice Dial Program view
default entity fax
Use the default entity faxcommand to set the default fax parameter settings globally.
Voice Dial Program view
28
3Com Router 5000/6000 Family
Command Reference
default entity modem compatible-param
Use the default entity modem compatible-paramcommand in the case that you fail to use standard
Modem PCM to interoperate with devices from other vendors.
Voice Dial Program view
default entity modem protocol
Use the default entity modem protocolnonecommand to globally disable Modem function of voice
entity.
Use the default entity modem protocolpcmcommand to globally configure PCM Modem protocol type
of voice entity, including coding/decoding and Modem negotiation mode.
Voice Dial Program view
default entity normal-connect slow-h245
Use the default entity normal-connect slow-h245command to globally disable the calling end from
actively initiating an H245 connection request to the called end before the called end is hooked off.
Use the default entity normal-connect slow-h245command to default to globally disable the calling
end from actively initiating the H245 connection request to the called end before the called end is hooked
off. In this case, all newly created voice entities and voice entities which have not been configured with this
function will inherit this configuration.
Voice Dial Program view
default entity payload-size
Use the default entity payload-sizecommand to configure the default time length of voice packets with
different coding formats.
Voice Dial Program view
default entity service data
Use the default entity service datacommand to globally configure enabling data call service.
Voice dial program view
default entity vad-on
default interval
default limit
Use the default entity vad-oncommand to globally configure enabling silence detection as the default
value.
Voice Dial Program view
Use the default intervalcommand to configure the default interval for OSPF to redistribute external
routes.
OSPF view
OSPF view
Use the default limitcommand to configure default value of maximum number of redistributed routes.
default local-preference
Use the default local-preferencecommand to configure the local preference.
BGP Unicast view
BGP Multicast view
VPNv4 view
default med
Use the default medcommand to configure the system MED value.
BGP Unicast view
BGP Multicast view
VPNv4 view
VPN Instance view
default-route-advertise
Use the default-route-advertisecommand to configure the default route of Level-1 and Level-2 routers.
IS-IS view
default-route-advertise
Use the default-route-advertisecommand to make the system generate a default route to OSPF area.
Use the default-route-advertisecommand at ABR to generate a default route which is advertised via
the Type-5 LSA or Type-7 LSA no matter whether there is a default route in the routing table.
OSPF view
BGP view
default-route imported
Use the default-route importedcommand to redistribute local default routes into BGP.
3Com Router 5000/6000 Family
Command Reference
29
default tag
Use the default tagcommand to configure the default tag of OSPF when it redistributes an external route.
OSPF view
OSPF view
default type
Use the default typecommand to configure the default type when OSPF redistributes external routes.
delay
Use the delaycommand to configure the related time parameters at the digital E&M subscriber-line (E1
controller).
Digital E&M Voice Subscriber-Line view
delay
Use the delaycommand to configure the relevant time parameters on an FXO or analog E&M
subscriber-line.
FXO Voice Subscriber-Line view
delay-reversal
Use the delay-reversalcommand to configure the timer's interval of polarity-reverse transmission delay
on FXS interfaces.
Voice Subscriber-Line view
delete
delete
Use the deletecommand to delete the specified file.
FTP Client view
SFTP Client view
Use the deletecommand to delete the specified file from the server as you would with the remove
command.
delete
Use the deletecommand to move the specified file from the storage device to the recycle bin, where you
can completely delete the file with the undeletecommand or restore it with the reset recycle-bin
filenamecommand.
User view
System view
System view
delete rpf-route-static all
Use the delete rpf-route-static allcommand to delete all the static multicast routes.
delete static-routes all
Use the delete static-routes allcommand to cancel all the static routes.
description
Use the descriptioncommand to configure port description. Identifying a port is the only function of this
command.
Ethernet Port view
description
description
description
Use the descriptioncommand to briefly describe a test operation.
HWPing Test Group view
Interface view
Use the descriptioncommand to describe the interface.
Use the descriptioncommand to configure description information for a specified VPN instance.
Vpn-Instance view
description (in Voice Entity View)
Use the descriptioncommand to configure a voice entity description string.
Voice Entity view
description (in Voice Subscriber-Line View)
Use the descriptioncommand to configure a subscriber-line description character string.
FXO Voice Subscriber-Line view
destination
Use the destinationcommand to specify the destination IP address to be filled in the added IP header at
the time of tunnel interface encapsulation.
Tunnel Interface view
30
3Com Router 5000/6000 Family
Command Reference
destination-ip
destination-port
detect
Use the destination-ipcommand to configure the destination IP address in the test.
Use the destination-portcommand to configure the destination port in the test.
Use the detectcommand to specify ASPF policy for application layer protocols.
HWPing Test Group view
HWPing Test Group view
ASPF Policy view
detect
Use the detectcommand to enable data carrier detection as well as level detection on a serial interface.
Asynchronous Serial Interface view
Synchronous Serial Interface view,
detect-ais (CE1/PRI Interface)
Use the detect-aiscommand to enable alarm indication signal (AIS) detect on the CE1/PRI interface.
CE1/PRI Interface view
System view
detect group
Use the detect-groupcommand to create a detect group and enter its view.
detect list
Use the detect-listcommand to add an IP address to the detect group and assign the address a detecting
sequence number.
Detect Group view
IKE Proposal view
dh
Use the dhcommand to select the Diffie-Hellman group for an IKE proposal.
dhcp accounting domain (Interface view)
Use the dhcp server accounting domaincommand to enable DHCP accounting for addresses from the
interface address pool and configure a domain for DHCP accounting.
Interface view
System view
dhcp enable
Use the dhcp enablecommand to enable DHCP.
dhcp relay information
Use the dhcp relay information enablecommand to enable the DHCP relay to support option 82
globally.
System view
System view
dhcp relay information strategy
Use the dhcp relay information strategycommand to configure a strategy for handling packets with
option 82 on the DHCP relay.
dhcp relay release
Use the dhcp relay releasecommand to send an IP address releasing request to a DHCP server via the
DHCP relay.
Interface view
System view
dchp select (Interface view)
Use the dhcp selectcommand in Interface view to select a method for disposing the DHCP packets
destined to the local device.
Interface view
System view
System view
dchp select (System view)
Use the dhcp selectcommand in System view to select a method for multiple interfaces in a specified
range to dispose the DHCP packets destined to the local device.
dhcp server accounting domain interface (System view)
Use the dhcp server accounting domain interfacecommand to enable DHCP accounting for addresses
from the address pools of the specified interfaces and configure a domain for DHCP accounting.
3Com Router 5000/6000 Family
Command Reference
31
dhcp server bims-server (Interface view)
Use the dhcp server bims-servercommand to enable and configure BIMS option support on the current
interface.
Ethernet Interface (or Subinterface) view
dhcp server bims-server interface (System view)
Use the dhcp server bims-server interfacecommand to enable and configure BIMS option support for
an interface or all interfaces configured with interface address pools.
System view
System view
dhcp server detect
Use the dhcp server detectcommand to enable pseudo-DHCP-server detection.
dhcp server dns-list
Use the dhcp server dns-listcommand in interface view to configure DNS IP addresses for an interface
configured with a DHCP address pool.
Ethernet Interface (or Subinterface) view
dhcp server dns-list interface (System view)
Use the dhcp server dns-list interfacecommand to assign DNS IP addresses to the DHCP address
pool of multiple interfaces in a specified range.
System view
dhcp server domain-name (Interface view)
Use the dhcp server domain-namecommand in interface view to configure the domain name that the
DHCP address pool of the current interface allocates to clients.
Ethernet Interface (or Subinterface) view
dhcp server domain-name interface (System view)
Use the dhcp server domain-name interfacecommand in system view to configure the domain name
that the DHCP address pool of the interfaces in a specified range allocates to DHCP clients.
System view
dhcp server expired (Interface view)
Use the dhcp server expiredcommand in interface view to configure a valid period allowed for leasing IP
addresses in the current interface DHCP address pool.
Ethernet Interface (or Subinterface) view
dhcp server forbidden-ip
Use the dhcp server forbidden-ipcommand to exclude IP addresses in a specified range to participate
in the auto-allocation.
System view
System view
dhcp server interface (System view)
Use the dhcp server expired interfacecommand in system view to configure a valid period allowed for
leasing IP addresses in the interface DHCP address pool of the interfaces in a specified range.
dhcp server ip-pool
Use the dhcp server ip-poolcommand to create a DHCP address pool and access the DHCP address
pool view.
System view
dhcp server nbns-list (Interface view)
Use the dhcp server nbns-listcommand in interface view to configure NetBIOS server addresses in the
DHCP address pool of current interface.
Ethernet Interface (or Subinterface) view
dhcp server nbns-list interface (System view)
Use the dhcp server nbns-list interfacecommand in system view to configure NetBIOS server
addresses for the clients that get ip address from the DHCP address pool of the interfaces in a specified
range.
System view
dhcp server netbios-type (Interface view)
Use the dhcp server netbios-typecommand in interface view to configure the NetBIOS node type of the
DHCP clients of the current interface.
Ethernet Interface (or Subinterface) view
dhcp server netbios-type interface (System view)
Use the dhcp server netbios-type interfacecommand in system view to configure a NetBIOS node
type for the DHCP clients of the interfaces in a specified range.
System view
32
3Com Router 5000/6000 Family
Command Reference
dhcp server option (Interface view)
Use the dhcp server optioncommand in interface view to configure a DHCP self-defined option for the
DHCP address pool of the current interface.
Ethernet Interface (or Subinterface) view
dhcp server option interface (System view)
Use the dhcp server optioncommand in system view to configure a DHCP self-defined option for the
interfaces in a specified range.
System view
dhcp server ping
Use the dhcp server pingcommand to configure the maximum number of ping packets that the DHCP
server is allowed to send and the longest time period that the DHCP server should wait for the response to
each ping packet.
System view
System view
dhcp server relay information enable
Use the dhcp server relay information enablecommand to enable the DHCP server to support option
82.
dhcp server static-bind
Use the dhcp server static-bindcommand to configure a static address binding in the DHCP address
pool of the current interface.
Ethernet Interface (or Subinterface) view
Interface view
dhcp server synchronize arp (Interface view)
Use the dhcp server synchronize arpcommand to enable authorized ARP for a DHCP interface address
pool.
dhcp server synchronize arp interface (System view)
Use the dhcp server synchronize arp interfacecommand to enable authorized ARP for specified
DHCP interface address pools.
System view
dhcp server voice-config (Interface view)
Use the dhcp server voice-configcommand to enable the DHCP server to send option 184 and
suboptions of 184 when it assigns addresses from the current interface address pool.
Interface view
dhcp server voice-config interface (System view)
Use the dhcp server voice-config interfacecommand to enable the DHCP server to send option 184
and suboptions of 184 when it assigns addresses from the specified interface address pool.
System view
Voice Entity view
Voice view
dial-prefix
Use the dial-prefixcommand to configure the prefix of the telephone number dialed by the voice entity.
Use the dial-programcommand to enter the voice dial program view.
dial-program
dialer bundle
dialer bundle-member
Use the dialer bundlecommand to configure a dialer bundle used by a dialer interface.
Dialer Interface view
Use the dialer bundle-membercommand to configure a physical interface included in a dialer bundle in
the Resource-Shared DCC application.
Physical Interface view
Physical or Dialer Interface view
Physical or Dialer Interface view
dialer call-in
Use the dialer call-incommand to enable ISDN callback according to ISDN caller ID.
dialer callback-center
Use the dialer callback-centercommand to enable the callback server function.
dialer circular-group
Use the dialer circular-groupcommand to add the physical interface to a dialer circular group specified
here.
Physical Interface view
3Com Router 5000/6000 Family
Command Reference
33
dialer disconnect
Use the dialer disconnectcommand to clear the dial-up link or the session link on the specified interface
at the PPPoE/PPPoA client.
Any view
dialer enable-circular
Use the dialer enable-circularcommand to enable Circular DCC.
Physical or Dialer Interface view
dialer group
Use the dialer-groupcommand to configure access control on the packets transmitted on a DCC interface
and to place the interface in an access control group.
Physical or Dialer Interface view
dialer isdn-leased
dialer isdn-leased
Use the dialer isdn-leasedcommand to configure an ISDN B channel (can be either the channel on a
BRI or PRI interface) to be the leased line.
Physical or Dialer Interface view
Use the dialer isdn-leased 128kcommand to configure 128K leased line connection.
Use the dialer isdn-leasednumbercommand to configure 64K leased line connection.
ISDN BRI Interface view
dialer number
Use the dialer numbercommand to configure a dial number for placing a call to a single remote end.
Physical or Dialer Interface view
dialer priority
Use the dialer prioritycommand to configure a priority for a physical interface in a dialer circular group
in the Circular DCC configuration.
Physical Interface view
dialer queue-length
Use the dialer queue-lengthcommand to configure the number of packets which comply with the "permit"
statement that can be buffered before a link is set up.
Physical or Dialer Interface view
dialer route
Use the dialer routecommand to allow a DCC interface to call the specified destination address (host or
network address) or to receive calls from multiple remote ends.
Physical or Dialer Interface view
dialer-rule
Use the dialer-rulecommand to configure the conditions of the data packet that can trigger a DCC call.
System view
dialer threshold
Use the dialer thresholdcommand to configure the traffic threshold of a link on the DCC interface so that
another link can be enabled to call the same destination address when the ratio of traffic on all connected
links on the DCC interface to the available bandwidth exceeds the preset percentage.
Dialer Interface view
dialer timer autodial
Use the dialer timer autodialcommand to configure the automatic dialing interval of DCC.
Physical or Dialer Interface view
dialer timer compete
Use the dialer timer competecommand to configure an idle interval for an interface after call contention
occurs on the interface.
Physical or Dialer Interface view
dialer timer enable
Use the dialer timer enablecommand to configure an interval for the next call attempt on an interface
after the link is disconnected.
Physical or Dialer Interface view
dialer timer idle
Use the dialer timer idlecommand to configure the interval that a link is allowed to be idle (in other
words, the interval when there is no packets which comply with the “permit” statements transmitted) after a
call has been set up on the interface.
Physical or Dialer Interface view
34
3Com Router 5000/6000 Family
Command Reference
dialer timer wait-carrier
Use the dialer timer wait-carriercommand to configure the timeout time of wait-carrier timer.
Physical or Dialer Interface view
dialer timer warmup
Use the dialer timer warmupcommand to set the length of the warmup timer on the router configured with
the dial-up backup function. It is the time that the router must wait for bringing the dial-up backup function
into effect after a reboot.
System view
dialer user
Use the dialer usercommand to configure remote user name for authenticating requests when calls are
received.
Dialer Interface view
differential-delay
Use the differential-delaycommand to set the maximum differential delay for the member links in the
IMA group.
IMA Group Interface view
dir
dir
dir
Use the dircommand to query for a specified file.
FTP Client view
Use the dircommand to view the files in the specified directory as you would with the lscommand.
SFTP Client view
Use the dircommand, you can view information about the specified file or directory in the router storage
device.
User view
direct listen-port
disconnect
Use the direct listen-port Xcommand to set the listening port for vty.
Vty User Interface view
FTP Client view
Any view
Use the disconnectcommand to disconnect from the remote FTP server but remain in FTP client view.
Use the display l2tp sessioncommand to view the current L2TP sessions.
display l2tp session
display l2tp tunnel
display l2tp user
Use the display l2tp tunnelcommand to view information of the current L2TP tunnels.
Use the display l2tp usercommand to view information about the current L2TP users.
Any view
Any view
display aaa unsent-h323-call-record
Use the display aaa unsent-h323-call-recordcommand to view the detail record information about the
calls failed to be sent.
Any view
Any view
Any view
Any view
Any view
display acl
Use the display aclcommand to view the rules of access control list.
Use the display alarm urgentcommand to view the stored alarms in a specified way.
Use the display arpcommand to view the ARP mapping table.
display alarm urgent
display arp
display arp timer aging
Use the display arp timer agingcommand to display the aging timer for dynamic ARP entries.
3Com Router 5000/6000 Family
Command Reference
35
display aspf all
Use the display aspf allcommand to view the information of all ASPF policies and sessions.
Any view
Any view
Any view
Any view
display aspf interface
Use the display aspf interfacecommand to view the interface configuration of the inspection policy.
display aspf policy
display aspf session
display atm class
Use the display aspf policycommand to view the configuration of a specific inspection policy.
Use the display aspf sessioncommand to view the information of the ASPF sessions.
Use the display atm classcommand to view the information about ATM-Class. By default, if no
ATM-Class name is specified, the information of all ATM-Class is displayed.
Any view
Any view
Any view
display atm interface
display atm map-info
display atm map-info
Use the display atm map-infocommand to view the information about the upper layer protocol mapping
table of ATM.
Use the display atm map-infocommand to display upper layer protocol map information about a specified
ATM interface.
Use the display atm map-infocommand to view the information about the upper layer protocol mapping
table of ATM.
Any view
Any view
Any view
Any view
display atm pvc-group
display atm pvc-info
display auto-config
display bgp l2vpn
Use the display atm pvc-groupcommand to view the information about PVC-Group.
Use the display atm pvc-infocommand to view the information about PVC.
Use the display auto-configcommand to view the status of auto-config.
Use the display bgp l2vpn allcommand to view system operating information and all L2VPN
information.
Any view
Any view
Any view
Any view
Any view
display bgp group
Use the display bgp groupcommand to view the information of peer groups.
display bgp multicast group
Use the display bgp multicast groupcommand to view the information about peer groups.
display bgp multicast network
Use the display bgp multicast networkcommand to view the routing information that MBGP advertises.
display bgp multicast peer
Use the display bgp multicast peercommand to view information about MBGP peers.
display bgp multicast routing
Use the display bgp multicast routingcommand to view the MBGP routing information whose IP
address is specified in the BGP routing table.
Any view
36
3Com Router 5000/6000 Family
Command Reference
display bgp multicast routing as-path-acl
Use the display bgp multicast routing as-path-aclcommand to view in the BGP routing table the
MBGP routes that match the specified AS path list.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display bgp multicast routing cidr
Use the display bgp multicast routing cidrcommand to view the routing information with non-natural
network mask (that is, classless inter-domain routing, CIDR).
display bgp multicast routing community-list
Use the display bgp multicast routing community-listcommand to view the routing information that
is permitted by the MBGP community list.
display bgp multicast routing community
Use the display bgp multicast routing communitycommand to view the routing information that
belongs to the specified MBGP community.
display bgp multicast routing different-origin-as
Use the display bgp multicast routing different-origin-ascommand to view AS routes with
different origins.
display bgp multicast routing peer
Use the display multicast routing peercommand to view the route received from or sent to the
specified multicast neighbor.
display bgp multicast routing regular-expression
Use the display bgp multicast routing regular-expression command to view the routing information
matching the specified AS regular expression.
display bgp multicast routing statistic
Use the display bgp multicast routing statisticcommand to view statistics of MBGP route
information.
Any view
Any view
Any view
display bgp network
display bgp paths
display bgp peer
Use the display bgp networkcommand to view the routing information that has been configured.
Use the display bgp pathscommand to view the information about AS paths
Use the display bgp peercommand to view the information of peer.
Use the display bgp multicast peer command to view the information of MBGP peer.
Use the display bgp vpnv4 peercommand to view the information of VPN peer.
Any view
display bgp routing
Use the display bgp routingcommand to view the BGP routing information in the BGP routing table.
Use the display bgp multicast routingcommand to view the MBGP routing information in the BGP
routing table.
Use the display bgp vpnv4 routingcommand to view the VPN routing information in the BGP routing
table.
Any view
Any view
display bgp routing as-path-acl
Use the display bgp routing as-path-aclcommand to view routes that match an as-path ACL.
display bgp routing cidr
Use the display bgp routing cidrcommand to view the routing information about the non-natural mask
(namely the classless inter-domain routing, CIDR).
Any view
3Com Router 5000/6000 Family
Command Reference
37
display bgp routing community
Use the display bgp routing communitycommand to view the routing information related to the specified
BGP community number in the routing table.
Any view
display bgp routing community-list
Use the display bgp routing community-listcommand to view the routing information matching the
specified BGP community list.
Any view
Any view
display bgp routing dampened
Use the display bgp routing dampenedcommand to view BGP dampened routes.
display bgp routing different-origin-as
Use the display bgp routing different-origin-ascommand to view routes that have different source
autonomous systems.
Any view
display bgp routing flap-info
Use the display bgp routing flap-infocommand to view BGP flap statistics. When
<network-address mask> is <0.0.0.0 0.0.0.0>, this command will view the flap statistics of all BGP
routes.
Any view
Any view
Any view
Any view
Any view
display bgp routing label
Use the display bgp routing labelcommand to view routing information and label information in the
BGP routing table.
display bgp routing peer { advertised | received }
Use the display bgp routing peercommand to view the routing information the specified BGP peer
advertised or received.
display bgp routing peer dampened
Use the display bgp routing peer dampenedcommand to view the information about the dampened
routes received from the specified peer.
display bgp routing peer regular-expression
Use the display bgp routing peer regular-expression command to view the route information
received from the specified peer and matching the specified regular expression.
display bgp routing regular-expression
Use the display bgp routing regular-expression command to view the routing information matching
the specified AS regular expression.
Any view
Any view
Any view
display bgp routing statistic
Use the display bgp routing statisticcommand to display statistics about BGP routes.
Use the display bgp vpnv4command to view VPNv4 information in BGP database.
display bgp vpnv4
display bootp client
Use the display bootp client |