Klipsch Speaker System SB 3 User Manual

Programming The Klipsch HD Theater SB 3 To Your TV Remote  
The Klipsch HD Theater SB 3 soundbar has four control buttons under the status indicator lights on its front panel. From the  
top button down, they are Source, MuTe, VoluMe up, and VoluMe Down. MuTe, VoluMe up and VoluMe Down can easily be  
programmed to your TV, Satellite or cable box remote control so that you can use that remote to control these functions.  
NOTE: The SB 3 model comes with its own remote and controls not only the four control buttons but has a separate button for  
the 3D Surround Mode on/off feature. The four control buttons can be programmed into other remote controls using the built-in  
learning remote feature, but the 3D Surround mode on/off button cannot be learned by any other remote and must be controlled  
with the included remote.  
STATUS LIGHTS  
SOURcE  
MUTE  
VOLUME DOWN VOLUME UP  
IMPORTANT NOTE: There is not a power on/off button on the front of the soundbar (there is a Main power switch on the soundbar’s rear  
panel). You do not need to turn off the soundbar (or subwoofer) when finished watching TV. when finished, turn off your TV (or Satellite or  
cable box if the soundbar is connected to that). The soundbar (and the subwoofer) will automatically go into a Standby or “sleep” mode  
if they do not receive an audio signal from your TV, Satellite or cable Box for approximately 10 minutes. Standby mode is indicated by a  
solid red status light on the soundbar front and on the subwoofer rear panel. when your TV, Satellite or cable box is turned back on and a  
signal is again received, the soundbar (and subwoofer) will automatically come out of Standby mode and turn on.  
Easy, Three-Step Remote Programming  
The following 3 steps should be used to program each function of your TV or cable box  
remote control buttons (MuTe, VoluMe up, and VoluMe Down). IF THE SOUNDBAR IS  
IN STANDBY MODE (solid reD status light), push the <Source> button on the sound-  
bar until the status light is solid Green.  
1
Red and Green (alternating)  
STEP ONE (Place the unit in learning mode): with the status light showing solid Green,  
press and hold the <Source> and <MuTe> buttons on the front of the soundbar at the  
same time (approximately 3 seconds) until the status light flashes reD and Green.  
2
Solid Orange  
STEP TWO (Select the function to learn): press the <MuTe> button once on the soundbar  
(the status light changes to solid orAnGe). (Substitute the VOLUME UP, and VOLUME DOWN  
in place of <MUTE> when programming the other buttons during this step)  
3
x4  
STEP THREE (Learn the function): Hold your remote control within one foot (30m) of the  
soundbar. Slowly press the <MuTe> button on your remote control four times. on the  
first three presses, the status indicator light will flicker orAnGe with each press. If the  
unit has successfully learned the function, on the fourth press of the button, the light  
will flash Green several times and then turn to solid Green. (Remember to use the  
VOLUME UP, and VOLUME DOWN in place of <MUTE> when programming the other  
buttons during this step)  
1 Foot  
To program the remaining functions, simply repeat all steps, substituting <MUTE>  
with the new function and button presses (VOLUME UP, and VOLUME DOWN) on steps  
TWO and THREE.  
© 2012 Klipsch Group, Inc.  
 

Invacare Camping Equipment CG9701 User Manual
IOGear Network Card GBS301 User Manual
JBL Portable Speaker S412PII User Manual
JVC Car Video System KD DV7302 User Manual
JVC MP3 Player HR XVC1U User Manual
Kalorik Ventilation Hood USK DKP 21898 User Manual
Kenmore Refrigerator 25331115308 User Manual
Kettler Bicycle 8718 710 720 730 750 User Manual
Klipsch Speaker IC SW 8T2 User Manual
Kodak Digital Camera V603 User Manual